Troubleshooting Guide

• Power-related problems
• Shooting-related problems
• Problems with wireless features
• Operation problems
• Display problems
• Playback problems
• Sensor cleaning problems
• Computer connection problems
• Problems with the multi-function shoe

If a problem occurs with the camera, first refer to this Troubleshooting Guide. If this Troubleshooting Guide does not resolve the problem, take the camera to the nearest Canon Service Center.

Power-related problems

• If the battery's remaining capacity () is 94% or higher, the battery will not be charged.
• Do not use any battery packs other than a genuine Canon Battery Pack LP-E6P/LP-E6NH/LP-E6N/LP-E6.
• In case of charging or charger issues, see Charging the Battery.

• Constant, rapid orange blinking of the lamp indicates that a protection circuit has stopped charging because (1) there is a problem with the battery charger or battery, or (2) communication with the battery failed (with a non-Canon battery, for example). In the case of (1), unplug the charger, reinsert the battery, and wait a few minutes before plugging the charger in again. If the problem persists, take the camera to the nearest Canon Service Center.

• For safety, hot or cold batteries inserted in the charger are not charged, and the lamp remains off. In this case, let the battery adjust to the ambient temperature before attempting to charge it again. During charging, if the battery's temperature becomes high for any reason, charging will stop automatically (lamp blinks). When the battery temperature goes down, charging will resume automatically.

• Batteries are not charged while the camera power switch is set to . However, batteries are charged during auto power off.
• Battery Pack LP-E6 cannot be charged.
• Batteries are not charged when their remaining capacity is already approx. 94% or higher.
• Operating the camera will stop charging in progress.

• In case of charging problems, the access lamp blinks in green and a protective circuit stops charging. In this case, unplug the power cord, reattach the battery, and wait a few minutes before plugging it in again. If the problem persists, take the camera to the nearest Canon Service Center.
• If batteries are hot or cold, the access lamp blinks in green and a protective circuit stops charging. In this case, let the battery adjust to the ambient temperature before attempting to charge it again.

• Try unplugging the USB power adapter and plugging it in again.

• Check the battery compartment. The camera cannot be powered without a battery pack.
• Check the remaining battery level. When batteries are depleted, the adapter charges them. In this case, power is not supplied to the camera.

• Make sure the battery is inserted properly in the camera ().
• Make sure the card slot cover is closed ().
• Charge the battery ().

• If the power is turned off while an image is being recorded to the card, the access lamp will remain on or continue to blink for a few seconds. When the image recording is complete, the power will turn off automatically.

• Do not use any battery packs other than a genuine Canon Battery Pack LP-E6P/LP-E6NH/LP-E6N/LP-E6.
• Remove and install the battery again ().
• If the electrical contacts are dirty, use a soft cloth to clean them.

• Use a fully charged battery ().
• The battery performance may have degraded. See [: Battery info.] to check the battery recharge performance level (). If the battery performance is poor, replace the battery with a new one.

• The number of available shots will decrease with any of the following operations:

  • Pressing the shutter button halfway for a prolonged period
  • Activating the AF frequently without taking a picture
  • Using the lens's Image Stabilizer
  • Using the wireless communication functions

• Auto power off is in effect. To deactivate auto power off, set [Auto power off] in [: Power saving] to [Disable] ().
• Even if [Auto power off] is set to [Disable], the screen and viewfinder will still turn off after the camera is left idle for the time set in [Screen off] or [Viewfinder off] (although the camera itself remains on).

Shooting-related problems

• To attach EF or EF-S lenses, you will need a mount adapter. The camera cannot be used with EF-M lenses ().

• Make sure the card is properly inserted ().
• Slide the card's write-protect switch to the Write/Erase setting ().
• If the card is full, replace the card or delete unnecessary images to make space (, ).
• Shooting is not possible if the AF point turns orange when you attempt to focus. Press the shutter button halfway again to refocus automatically, or focus manually (, ).

• If a card error message is displayed, see Inserting/Removing Cards and Error Codes.

• Since SDXC cards are formatted in exFAT, if you format a card with this camera and then insert it into another camera, an error may be displayed and it may not be possible to use the card.

• Set the focus mode to ().
• Press the shutter button gently to prevent camera shake ().
• With a lens equipped with an Image Stabilizer, set the Image Stabilizer switch to .
• In low light, the shutter speed may become slow. Use a faster shutter speed (), set a higher ISO speed (), use flash (), or use a tripod.
• See Minimizing blurred photos.

• Set the AF operation to One-Shot AF (). Shooting with the focus locked is not possible with Servo AF ().

• High-speed continuous shooting may be slower depending on the battery level, ambient temperature, flicker reduction, shutter speed, aperture value, subject conditions, brightness, AF operation, type of lens, use of flash, shooting settings, and other conditions. For details, see Selecting the Drive Mode or Still photo file size / Number of shots available.

• Shooting intricate subjects such as fields of grass may result in larger file sizes, and the actual maximum burst may be lower than the guidelines in Still photo file size / Number of shots available.

• Estimated maximum burst indicated in the viewfinder does not change when you switch cards, even if you switch to a high-speed card. Maximum burst listed in Still photo file size / Number of shots available is based on the standard Canon test card, and the actual maximum burst is higher for cards with faster writing speeds. For this reason, estimated maximum burst may differ from actual maximum burst.

• Refer to the high-speed display requirements in High-Speed Display.

• Aspect ratios cannot be set when [: Add cropping information] is set to an option other than [Disable].

• The minimum speed in the ISO speed range is ISO 200 when [: Highlight tone priority] is set to [Enable] or [Enhanced].

• Check the [ISO speed range] setting under [: ISO speed settings].
• Expanded ISO speeds are not available when [: Highlight tone priority] is set to [Enable] or [Enhanced].
• Expanded ISO speeds are not available when [: HDR shooting ] is set to [Enable].

• Set [: Auto Lighting Optimizer] to [Disable] (). When [Low], [Standard], or [High] is set, even if you set a decreased exposure compensation or flash exposure compensation, the image may come out bright.

• See M: Manual Exposure to set the exposure compensation.

• With [Digital Lens Optimizer] set to [Standard] or [High], [Chromatic aberr corr] and [Diffraction correction] are not displayed, but they are both set to [Enable] for shooting.
• During movie recording, [Digital Lens Optimizer] or [Diffraction correction] are not displayed.

• Set [Slow synchro] in [: External Speedlite control] to [1/320-1/60 sec. auto] (or [1/250-1/60sec. auto]) or [1/320 sec. (fixed)] (or [1/250 sec. (fixed)]) ().

• Make sure any flash units are securely attached to the camera.

• Flash units other than EL/EX series Speedlites used in autoflash mode always fire at full output ().
• The flash always fires at full output when [Flash metering mode] in external flash Custom Function settings is set to [1:TTL] (autoflash) ().

• If flash exposure compensation is already set with the Speedlite, flash exposure compensation cannot be set with the camera. When the Speedlite's flash exposure compensation is canceled (set to 0), flash exposure compensation can be set with the camera.

• Set [Slow synchro] in [: External Speedlite control] to an option other than [1/320 sec. (fixed)] (or [1/250 sec. (fixed)]) ().

• In still photo shooting, set the drive mode to [] or [] (). In movie recording, set [: Remote control] to [Enable] ().
• Check the position of the remote control's release timing switch.
• If you are using Wireless Remote Control BR-E1, see Remote Control Shooting or Connecting to a Wireless Remote Control.
• Infrared remote controllers such as the RC-6 cannot be used for remote control shooting when the camera is paired via Bluetooth with a smartphone or wireless remote control. Set [Bluetooth settings] to [Disable].
• To use a remote control for time-lapse movie recording, see Time-Lapse Movies.

• Indicates that the camera's internal temperature is high. For details, see the information on warning indicator display in movie recording ().

• If the card's writing speed is slow, movie recording may stop automatically. For details on cards that can record movies, see Card performance requirements. To find out the card's writing speed, refer to the card manufacturer's website, etc.
• Perform low-level formatting to initialize the card if the card's writing or reading speed seems slow ().
• Recording stops automatically once your movie reaches 6 hr. (or 1 hr. 30 min. for a High Frame Rate movie).

• ISO speed is set automatically in [] recording mode. In [] mode, you can manually set the ISO speed ().
• The minimum speed in the ISO speed range is ISO 200 when [: Highlight tone priority] is set to [Enable] or [Enhanced].

• Check the [ISO speed range] setting under [: ISO speed settings].
• Expanded ISO speeds are not available when [: Highlight tone priority] is set to [Enable] or [Enhanced].

• If you change the shutter speed or aperture value during movie recording, the changes in the exposure may be recorded.
• Recording a few test movies is recommended if you intend to perform zooming during movie recording. Zooming as you record movies may cause exposure changes or lens sounds to be recorded, or loss of focus.

• Flickering, horizontal stripes (noise), or irregular exposures can be caused by fluorescent lighting, LED lighting, or other light sources during movie recording. Also, changes in the exposure (brightness) or color tone may be recorded. In [] mode, using a slower shutter speed may reduce the problem. The problem may be more noticeable in time-lapse movie recording.

• If you move the camera to the left or right (panning) or shoot a moving subject, the image may look distorted. The problem may be more noticeable in time-lapse movie recording.

• Sound is not recorded in High Frame Rate movies.

• Time codes are not added when you record High Frame Rate movies with [Count up] in [: Time code] set to [Free run] (). Additionally, no time code is added to HDMI video output ().

• Time codes in High Frame Rate movie recording advance 4 sec. per second ().

• Still photos cannot be taken during movie recording. To shoot still photos, stop recording the movie, then select a shooting mode for still photos.

• It may not be possible to record movies during still photo shooting if operations such as extended Live View display increase the camera's internal temperature. Turn off the camera or take other measures, and wait until the camera cools down.
• Reducing the movie recording size may enable recording.

• Image stabilization by the camera may make the camera seem to vibrate. This does not indicate damage.

Problems with wireless features

• Use a smartphone compliant with Bluetooth Specification Version 4.1 or later.
• Turn on Bluetooth from the smartphone settings screen.
• Pairing with the camera is not possible from the smartphone's Bluetooth settings screen. Install the dedicated app Camera Connect (free of charge) on the smartphone ().
• Pairing with a previously paired smartphone is not possible if pairing information registered for another camera remains on the smartphone. In this case, remove the camera's registration retained in the Bluetooth settings on the smartphone and try pairing again ().

• If the camera is connected to a computer or another device with an interface cable, Wi-Fi functions cannot be set. Disconnect the interface cable before setting any functions ().

• Other devices, such as computers, cannot be used with the camera by connecting them with an interface cable while the camera is connected to devices via Wi-Fi. Terminate the Wi-Fi connection before connecting the interface cable.

• With a Wi-Fi connection established, operations such as shooting and playback may not be possible. Terminate the Wi-Fi connection, then perform the operation.

• Even with a combination of the same camera and smartphone, if you have changed the settings or selected a different setting, reconnection may not be established even after selecting the same SSID. In this case, delete the camera connection settings from the Wi-Fi settings on the smartphone and set up a connection again.
• A connection may not be established if Camera Connect is running when you reconfigure connection settings. In this case, quit Camera Connect for a moment and then restart it.

• Update the printer firmware.
• Connect using the printer as an access point.
• On the camera, set [Security] to [WPA2] ().

Operation problems

• Separate settings are retained for use when shooting still photos and recording movies.

• Press the button to release the Multi-function lock ().
• Check the [: Multi function lock] setting ().

• Make sure [: Touch control] is set to [Standard] or [Sensitive] ().

• In movie recording, check the [: Shutter btn function for movies] setting ().
• Check the [: Customize buttons], [: Customize dials], and [Switch / when shooting] settings (, , ).

Display problems

• Tabs and items on the menu screen vary for still photos and movies.

• [Menu display] on the [] tab is set to [Display from My Menu tab] or [Display only My Menu tab]. Set [Normal display] ().

• Set [: Color space] to [sRGB]. If [Adobe RGB] is set, the first character will be an underscore ().

• [: File name] is set to [*** + image size]. Select either the camera's unique file name or the file name registered in User setting 1 ().

• If the card already contains recorded images, the image number may not start from 0001 ().

• Make sure the correct date and time are set ().
• Check the time zone and daylight saving time ().

• The shooting date and time do not appear in the image. The date and time are recorded in the image data as shooting information. When you print photos, this information can be used to include the date and time ().

• If the number of images recorded on the card exceeds the number the camera can display, [###] will be displayed.

• If the screen is dirty, use a soft cloth to clean it.
• The screen display may seem slightly slow in low temperatures or may look black in high temperatures, but it will return to normal at room temperature.

Playback problems

• [: Highlight alert] is set to [Enable] ().

• [: AF point disp.] is set to [Enable] ().

• AF points are not displayed when the following types of images are played back:

  • Images taken with Multi Shot Noise Reduction applied.
  • Cropped images.
  • Images from HDR shooting with [Auto Image Align] set to [Enable].

• If the image is protected, it cannot be erased ().

• The camera may not be able to play back images taken with another camera.
• Movies edited with a computer cannot be played back with the camera.

• The images have been filtered for playback with [: Set image search conditions] (). Clear the image search conditions.

• The camera's built-in microphone may also record mechanical sounds of the lens or sounds of camera/lens operations if AF operations are performed or the camera or lens is operated during movie recording. If so, it may help reduce these sounds if you use an external microphone equipped with an output plug and position it away from the camera and lens.

• Extended movie playback or movie playback under high ambient temperature may cause the camera's internal temperature to rise, and movie playback may stop automatically.

  If this happens, playback is disabled until the camera's internal temperature decreases, so turn off the power and let the camera cool down a while.

• Significant change in the exposure level during autoexposure movie recording may cause recording to stop momentarily until the brightness stabilizes. In this case, record in [] mode ().

• High Frame Rate movies are recorded at 29.97 fps or 25.00 fps, so they are played in slow motion at 1/4 speed.

• Make sure [: Video system] is set to [For NTSC] or [For PAL] correctly for the video system of your television.
• Make sure the HDMI cable's plug is inserted all the way in ().

• If the movie file size reaches 4 GB, another movie file will be created automatically (). However, if you use an SDXC card formatted with the camera, you can record a movie in a single file even if it exceeds 4 GB.

• Depending on the card reader used and the computer's operating system, SDXC cards may not be correctly recognized. In this case, connect the camera to the computer with the interface cable, then import the images to the computer using EOS Utility (EOS software, ).

• This camera cannot resize JPEG images, RAW images, or frame-grab images from 4K movies saved as still photos ().
• This camera cannot crop RAW images or frame-grab images from 4K movies saved as still photos ().

• White, red, or blue dots of light may appear in captured images if the sensor is affected by cosmic rays or similar factors. Their appearance may be reduced by performing [Clean now] under [: Sensor cleaning] ().

Sensor cleaning problems

• Although there is a mechanical sound from the shutter during cleaning after [Clean now] is selected, no image is recorded to the card ().

• Repeatedly turning the power switch and within a short period may prevent the [] icon from being displayed ().

Computer connection problems

• Install EOS Utility (EOS software) on the computer ().
• Make sure the main EOS Utility window is displayed.
• If the camera is already connected via Wi-Fi, it cannot communicate with any computer connected with an interface cable.
• Check the version of the application.

• When using EOS Utility (EOS software), set [: Time-lapse movie] to [Disable] ().

Problems with the multi-function shoe

• If [Communication error Reattach accessory] is displayed, reattach the accessory. In case this message is displayed again after reattachment, make sure the terminals of the multi-function shoe and accessory are clean and dry. If you cannot remove the dirt or moisture, contact a Canon Service Center.
• If [Accessory unavailable status] is displayed, check the terminals of the multi-function shoe and accessory and make sure the accessory is not damaged.