Still Photo Shooting

The camera analyzes the scene and sets the optimum settings automatically. It can also adjust focus automatically on either the still or moving subject by detecting the motion of the subject ().

  1. Set the still photo shooting/movie recording switch to Still photos.

  2. Select an Scene Intelligent Auto Assist feature.

    • Tap [Creative Assist] to access the selection screen ().

  3. Aim the camera at what you will shoot (the subject).

    • An AF point (1) may be displayed on the subject, under some shooting conditions.
    • When an AF point is displayed on the screen, aim it over the subject.

  4. Focus on the subject.

    • Press the shutter button halfway to focus.
    • Under low light, the AF-assist beam () is automatically activated if needed.
    • Once the subject is in focus, that AF point turns green and the camera beeps (One-Shot AF).
    • An AF point in focus on a moving subject turns blue and tracks subject movement (Servo AF).

  5. Take the picture.

    • Press the shutter button completely to take the picture.
    • The image just captured will be displayed for approx. 2 sec. on the screen.

Caution

  • Subject movement (whether subjects are still or moving) may not be detected correctly for some subject or shooting conditions.

Note

  • AF operation (One-Shot AF or Servo AF) is set automatically when you press the shutter button halfway. Even when automatically set to One-Shot AF, the camera will switch to Servo AF if subject motion is detected while you are pressing the shutter button halfway.
  • The Scene Intelligent Auto mode makes the colors look more impressive in nature, outdoor, and sunset scenes. If you do not obtain the desired color tones, change the mode to a Creative Zone mode () and select a Picture Style other than [Auto], then shoot again ().

Tips Minimizing blurred photos

  • Be careful about camera shake in handheld shots. To avoid camera shake, consider using a tripod. Use a sturdy tripod that can bear the weight of the shooting equipment. Attach the camera securely to the tripod.
  • Using a wireless remote control (sold separately, ) is recommended.

Troubleshooting FAQ

  • Focusing is not possible (indicated by a yellow AF point).

    Aim the AF point over an area with good contrast, then press the shutter button halfway (). If you are too close to the subject, move away and shoot again.

  • Multiple AF points are displayed simultaneously.

    Focus has been achieved at all those points.

  • The shutter speed display is blinking.

    Since it is too dark, taking the picture may result in a blurred subject due to camera shake. Using a tripod or an external flash () is recommended.

  • Pictures taken with flash are too bright.

    Pictures may be bright (overexposed) if you shoot subjects at close range in flash photography. Move away from the subject and shoot again.

  • The bottom part of pictures taken with flash is unnaturally dark.

    Shooting subjects that are too close may make the shadow of the lens visible in your shots. Move away from the subject and shoot again.

Note

  • Note the following if you are not using flash.

    • Under low light, when camera shake tends to occur, hold the camera steady or use a tripod. You can reduce the blur caused by camera shake by setting the lens to the wide-angle end.
    • When shooting portraits under low light, tell subjects to stay still until you have finished shooting. Any movement as you shoot will make the person look blurry in the picture.

Shooting Moving Subjects

Pressing the shutter button halfway tracks moving subjects to keep them in focus.

Keep the subject on the screen as you hold down the shutter button halfway, and at the decisive moment, press the shutter button completely.

Scene Icons

The camera detects the scene type and sets everything automatically to suit the scene. An icon representing the detected scene appears in the upper left of the screen () in still photo shooting, or when you press the movie shooting button to record a movie with the Mode dial set to Scene Intelligent Auto.

Adjusting Settings

By tapping icons on the screen, you can adjust settings for drive mode, image quality, Touch Shutter, Scene Intelligent Auto Assist, and Creative Assist.

A+: Assist Features

Selecting Scene Intelligent Auto Assist Features

  1. Select [Shooting:  Assist].

  2. Select an option.

Note

  • From the shooting screen, you can access the selection screen directly by tapping [Creative Assist] ().

Creative Assist

You can shoot with your preferred effects applied.

  1. Press Quick Control/Set.

    • Read the message and select [OK].

  2. Select an effect.

    • Select an effect with the Control dial dial and press Quick Control/Set.

  3. Select the effect level and other details.

    • Set with the Control dial dial and press Quick Control/Set.
    • To reset the setting, press the AE lock button, then select [OK].

Creative Assist effects

  • [Preset] Preset

    Select one of the preset effects.

    Note that [Saturation], [Color tone 1], and [Color tone 2] are not available with [B&W].

  • [Background blur] Background blur

    Adjust background blur. Choose higher values to make backgrounds sharper. To blur the background, choose lower values. [Auto] adjusts background blurring to match the brightness. Depending on the zoom position, some positions may not be available.

  • [Brightness] Brightness

    Adjust image brightness.

  • [Contrast] Contrast

    Adjust contrast.

  • [Saturation] Saturation

    Adjust the vividness of colors.

  • [Color tone 1] Color tone 1

    Adjust amber/blue color tone.

  • [Color tone 2] Color tone 2

    Adjust green/magenta color tone.

  • [Monochrome] Monochrome

    Set the toning effect for monochrome shooting.

Note

  • [Background blur] is not available in flash photography.
  • These settings are reset when you switch shooting modes or turn the power off. To save the settings, set [Shooting: Retain Creative Assist data] to [Enable].

Advanced Scene Intelligent Auto

Compositing and other advanced processing is applied to your shots based on scene detection by the camera.

  1. Select [Shooting:  Assist] ().

  2. Select [Advanced ].

  3. Check the icon.

    • Blinking scene icon (1): Multiple images are captured per shot and merged into a single image. In this case, only the composite image is saved.
    • Normal scene icon display: Shooting with Scene Intelligent Auto settings ().

Caution

  • Continuous shooting is not available.
  • The camera shoots in [Electronic ] shutter mode.
  • The image area is smaller than in other shooting modes.
  • RAW image quality cannot be selected.
  • Flash photography is not available.
  • Images that are greatly out of alignment due to camera shake or other issues may not be aligned correctly.
  • To prevent camera shake, a high ISO speed may be set.
  • Note that the image may not be rendered with a smooth gradation and may look uneven or noisy.
  • The image processing may not be sufficient in scenes with strong backlighting or high contrast.
  • Shooting moving subjects may result in afterimages from the movement, or darkness around the subject.
  • The image alignment may not function properly with repetitive patterns (lattice, stripes, etc.), flat or single-tone images, or images significantly misaligned due to camera shake.
  • Be careful about camera shake in handheld shots.
  • Shooting under fluorescent or LED lighting may cause issues such as irregular exposure or colors in the resulting images, due to the flickering light source.
  • [BUSY] appears on the screen as images are processed, and shooting is not possible until processing is finished.
  • Shots will look slightly different from the preview image shown on the screen.