Basic Communication Settings
- Connecting via Wired LAN
- Connecting via WPS
- Connecting to Detected Networks
- Connecting by Entering a Network Name
- Connecting in Camera Access Point Mode
- Setting the IP Address Manually
- Configuring IPv6
- Registering Sets of Communication Settings as Connection Settings
This section describes how to configure communication settings and register them in [Comm settings].
If communication settings are displayed when you are configuring network features, choose a connection method in the links above and follow the steps on the screen displayed ([Comm settings] or [LAN type] screen).
Connecting via Wired LAN
Register communication settings that involve a wired LAN as follows.
Adding the connection with the wizard
-
In [Network], select [Enable].
-
Select [Manual setting].
-
Select [Comm settings].
-
Select [NW*].
-
Select [Create with wizard].
-
Select an option.
- Select [OK] to go to the next screen.
- Selecting [Configure offline] will keep the camera disconnected from the network after configuration.
-
Select [Wired].
- Select [OK] to go to the next screen.
-
Select an option.
- Select [OK] to go to the next screen.
- If you have selected [Manual setting], also see Setting the IP Address Manually.
-
Select use of IPv6.
-
Press .
- The communication settings are saved.
Connecting via WPS
Register communication settings with WPS (Wi-Fi Protected Setup) as follows.
WPS connections
Options for connection methods include push-button configuration (PBC) and personal identification number (PIN). When establishing a connection, check the method supported by your access point.
PBC
The camera and access point can be connected simply by pressing the WPS button on the access point.
- Connecting may be more difficult if multiple access points are active nearby. If so, try to connect with [WPS (PIN mode)].
- Check the position of the WPS button on the access point in advance.
- It may take approx. 1 min. to establish a connection.
PIN
An 8-digit identification number indicated on the camera is entered on the access point to establish a connection.
- Even if multiple access points are active nearby, connecting by using this shared identification number is relatively reliable.
- It may take approx. 1 min. to establish a connection.
Adding the connection with the wizard
-
In [Network], select [Enable].
-
Select [Manual setting].
-
Select [Comm settings].
-
Select [NW*].
-
Select [Create with wizard].
-
Select [Configure online].
- Select [OK] to go to the next screen.
-
Select [Wi-Fi ].
- Select [OK] to go to the next screen.
-
Select [Connect with WPS].
-
Select an option.
- Select [OK] to go to the next screen.
For [WPS (PBC mode)]
- Press the access point's WPS button. For details on where the button is and how long to press it, refer to the access point user manual.
- Select [OK] to initiate connection with the access point.
- Go to step 12 after the camera is connected to the access point.
For [WPS (PIN mode)]
- On the access point, enter the 8-digit PIN code displayed on the camera screen. For instructions on entering PIN codes on the access point, refer to the access point's Instruction Manual.
- Select [OK] to go to the next screen.
-
Connect to the access point.
- Select [OK] to initiate connection with the access point.
- The following screen is displayed once the camera is connected to the access point.
-
Select [Auto setting].
- Select [OK] to go to the next screen.
- If you have selected [Manual setting], also see Setting the IP Address Manually.
-
Select use of IPv6.
-
Press .
- The communication settings are saved.
Connecting to Detected Networks
Register communication settings by choosing the network name from a list of detected access points.
Adding the connection with the wizard
-
In [Network], select [Enable].
-
Select [Manual setting].
-
Select [Comm settings].
-
Select [NW*].
-
Select [Create with wizard].
-
Select [Configure online].
- Select [OK] to go to the next screen.
-
Select [Wi-Fi ].
- Select [OK] to go to the next screen.
-
Select the network name.
- Use the dial to select the name of the network for the connection.
- [] in the list indicates that the access point supports the 6 GHz band.
Note
-
[Refresh]
- To display [Refresh], scroll down the screen in step 9.
- Select [Refresh] to search for access points again.
-
Enter the password.
-
Select [Auto setting].
- Select [OK] to go to the next screen.
- If you have selected [Manual setting], also see Setting the IP Address Manually.
-
Select use of IPv6.
-
Press .
- The communication settings are saved.
Connecting by Entering a Network Name
Connect to an access point by selecting its SSID (or ESS-ID) in a list of active access points nearby.
Adding the connection with the wizard
-
In [Network], select [Enable].
-
Select [Manual setting].
-
Select [Comm settings].
-
Select [NW*].
-
Select [Create with wizard].
-
Select [Configure offline].
- Select [OK] to go to the next screen.
-
Select [Wi-Fi ].
- Select [OK] to go to the next screen.
-
Select [Infrastructure].
- Select [OK] to go to the next screen.
-
Enter the SSID (network name).
-
Select the type of security.
- Select [OK] to go to the next screen.
- The same type of security must be set on both the other device and the camera. See Authentication and data encryption methods for details on types of authentication and encryption.
-
Enter the password.
-
Select an option.
- Select [OK] to go to the next screen.
- If you have selected [Manual setting], also see Setting the IP Address Manually.
-
Select use of IPv6.
-
Press .
- The communication settings are saved.
Connecting in Camera Access Point Mode
Register communication settings for direct connections between the camera and other devices.
Adding the connection with the wizard
-
In [Network], select [Enable].
-
Select [Manual setting].
-
Select [Comm settings].
-
Select [NW*].
-
Select [Create with wizard].
-
Select an option.
- Select [OK] to go to the next screen.
- Selecting [Configure offline] will keep the camera disconnected from the network after configuration.
-
Select [Wi-Fi ].
- Select [OK] to go to the next screen.
-
Select [Camera access point mode].
[Configure online] options
[Configure offline] options
-
Select an option.
-
Enter the SSID (network name).
-
Select a channel setting option.
- To specify the settings manually, select [Manual setting], then turn the dial.
- Select [OK] to go to the next screen.
-
Select the type of security.
- Select [OK] to go to the next screen.
- If you have selected [None], the [IP address setting (IPv4)] screen is displayed ().
- Available options vary depending on the [Channel setting] option you chose.
- The same type of security must be set on both the other device and the camera. See Authentication and data encryption methods for details on types of authentication and encryption.
-
Enter the password.
-
Select how to set the IP address.
- Select [OK] to go to the next screen.
- If you have selected [Manual setting], also see Setting the IP Address Manually.
-
Check the SSID and password.
- Select [OK] to go to the next screen.
-
Press .
- The communication settings are saved.
Setting the IP Address Manually
Set the IP address as follows if you have selected [Manual setting] on the [IP address setting (IPv4)] screen.
-
Select [Manual setting].
- Select [OK] to go to the next screen.
-
Select an option to configure.
- The items displayed vary depending on the communication function.
- Select an option to access the screen for numerical input.
-
To use a gateway, select [Enable], then select [Address].
-
To use a DNS address, select [Manual setting], then select [Address].
-
Enter the number.
- To set the entered numbers and return to the screen for step 2, press the button.
-
Select [OK].
- When you have completed setting the necessary items, select [OK].
- If you are unsure what to enter, see Checking Network Settings or ask the network administrator or other person in charge of the network.
-
Select use of IPv6.
-
Press .
- The communication settings are saved.
Configuring IPv6
To use IPv6, configure the settings manually.
Note
- If you are unsure what to enter, ask the network administrator or other person in charge of the network.
-
Select [Manual setting].
-
Select [Comm settings].
-
Select the communication settings that will use IPv6.
-
Select [Change].
-
Select [TCP/IPv6].
-
Select an option to configure.
-
Use TCP/IPv6
- Select [Enable] or [Disable] for IPv6.
-
Manual setting
- To set the IP address manually, select [Enable]. [DNS server] is set to [Manual setting], and you can configure [DNS address], [Manual address], [Prefix length], and [Gateway].
-
DNS server
- To set the DNS server IP address manually, select [Manual setting].
- Select [Disable] if you will not use a DNS server.
- If the setting is currently [Auto assign], setting [Manual setting] to [Enable] changes it to [Manual setting].
-
DNS address/Manual address/Gateway
-
Select an option and enter the IP address.
-
-
Prefix length
- To set the prefix length, turn the dial to select a value (0–128).
-
Registering Sets of Communication Settings as Connection Settings
You can register multiple communication settings (combinations of wired LAN and Wi-Fi settings, or multiple Wi-Fi settings) as a single set of connection settings.
With a combination of wired LAN and Wi-Fi settings, communication is restricted to the wired LAN when it is available but otherwise switches to the Wi-Fi connection. When the wired LAN becomes available again, communication is restricted to it.
This section explains how to register connection settings using function and communication settings that are already configured.
Caution
- Settings for multiple networks cannot be configured in camera access point mode settings.
-
Select [Connection settings].
-
Select [SET*].
-
Select [Create from list].
-
Select [Func settings *].
-
Select [Select from list].
-
Select function settings.
-
The function settings are registered, and display returns to the [Change] screen.
-
-
Select [Comm settings 1].
-
Select [Select from list].
-
Select communication settings.
- The first communication settings are registered, and display returns to the [Change] screen.
- You can register wired LAN or Wi-Fi settings in any order.
-
Select [Comm settings 2].
-
Select [Select from list].
-
Select communication settings.
- Select Wi-Fi settings if wired LAN settings are already registered in [Comm settings 1], or select wired LAN settings if Wi-Fi settings are already registered in [Comm settings 1].
Note
- If Wi-Fi settings are already registered in [Comm settings 1], you can select Wi-Fi settings for [Comm settings 2].
-
Exit the screen for changing settings.
- Press the button.
-
Select [Connect].
-
Select [OK].
- The connection is initiated.