Other Menu Functions

[Shooting2]

Exposure comp.

Exposure compensation can be adjusted in a range of ±3 stops, in 1/3-stop increments. For details on exposure compensation, see Manual Exposure Compensation.

MovieISO speed settings

  • ISO speed

    In [Movie manual exposure] mode, you can set the ISO speed manually. You can also select ISO Auto.

  • ISO speed range

    You can set the manual ISO speed setting range (minimum and maximum). ISO expansion can also be configured.

  • Max for Auto

    You can set the maximum limit for ISO Auto in movie recording in [Movies], [Shutter-priority AE (movies)], or [Aperture-priority AE (movies)] mode or in [Movie manual exposure] mode with ISO Auto.

  • Time-lapse movieMax for Auto

    You can set the maximum limit for ISO Auto in 4K time-lapse/Full HD time-lapse movie recording in [Movies], [Shutter-priority AE (movies)], or [Aperture-priority AE (movies)] mode or in [Movie manual exposure] mode with ISO Auto.

[Shooting3]

MovieAv 1/8-stop incr.

You can set aperture values on a finer scale when recording movies with RF or RF-S lenses.

This feature is available in [Movie manual exposure] or [Aperture-priority AE (movies)] recording mode.

Select [Enable] to change the aperture increment from 1/3 stop (or 1/2 stop) to 1/8 stop.

Caution

  • [MovieAv 1/8-stop incr.] is not available (not displayed) when EF or EF-S lenses are used.
  • When set to [Enable], setting options in [Custom Functions: Exposure level increments] are disabled and have no effect.

Movie Auto slow shutter

You can choose whether to record movies that are brighter and less affected by image noise than when set to [Disable] by automatically slowing the shutter speed under low light.

Available in [Movies] or [Aperture-priority AE (movies)] recording mode. Applies when the frame rate of the movie recording size is 59.94 fps or 50.00 fps.

  • Disable

    Enables you to record movies with smoother, more natural movement, less affected by subject shake than when set to [Enable]. Note that under low light, movies may be darker than when set to [Enable].

  • Enable

    Enables you to record brighter movies than when set to [Disable] by automatically reducing the shutter speed to 1/30 sec. (NTSC) or 1/25 sec. (PAL) under low light.

Note

  • Setting to [Disable] is recommended when recording moving subjects under low light, or when afterimages such as trails may occur.

[Shooting5]

Lens aberration correction

Peripheral illumination, distortion, focus breathing, and chromatic aberration can be corrected as you record movies. For details on lens aberration correction, see Lens Aberration Correction.

[Shooting8]

Standby: Low res.

Set to [On] to conserve battery power and control the rise of internal camera temperature during standby.

As a result, it may enable you to record movies over a longer period.

Caution

  • The standby screen may differ from the movie recording screen in details such as image quality and angle of view.
  • Briefly when you start recording movies, image display may remain on the current frame instead of being updated.
  • [Shooting: Standby: Low res.] is set to [Off] and cannot be changed in the following cases.
    • When [Shooting: Digital zoom] is set to [On] ()
    • When [Shooting: Pre-recording set.] is set to [On] ()

HDMI display

You can specify how movies are displayed as they are recorded via HDMI to an external device. Movie output itself corresponds to the [Movie rec. size] setting.

The default setting is [External screen].

  • Live View shooting+External monitor

    Enables movie display both on the camera screen and on the other device, via HDMI output.

    Camera operations such as image playback or menu display are shown on the other device via HDMI, not on the camera screen.

  • External screen

    Deactivates the camera screen during output via HDMI, so that the screen is blank.

    Shooting information, AF points, and other information is included in HDMI output and shown on any monitors connected to the external recording device, but you can stop output of this information by pressing the INFO button.

    Before recording movies externally, confirm that no information is being sent by the camera by making sure no shooting information, AF points, and so on is displayed on external monitors or other devices.

Caution

  • Card recording is not performed with [Shooting: HDMI display] set to [Live View shooting+External monitor]. Camera menus and image playback are only displayed on the screen connected via HDMI.
  • The HDMI output resolution and frame rate are automatically adjusted to suit the movie recording size.

Troubleshooting For longer HDMI output

To continue HDMI output for longer than 30 min., select [Live View shooting+External monitor], then set [Auto power off] in [Set-up: Power saving] to [Disable] (). HDMI output will continue after the camera screen turns off when the time set in [Screen off] elapses.

Caution

  • HDMI output without information prevents display of warnings about the card space, battery level, or high internal temperature () via HDMI.
  • During HDMI output, display of the next image may take some time if you switch between movies of different recording sizes or frame rates.
  • Avoid operating the camera when recording movies to external devices, which may cause information to be displayed in the HDMI video output.
  • Brightness and color of movies recorded with the camera may look different from that of HDMI video output recorded by external devices, depending on the viewing environment.

Note

  • By pressing the INFO button, you can change the information displayed.
  • Time codes can be added to HDMI video output ().
  • Audio is also output via HDMI, except when [Sound rec.] is set to [Disable].

HDMI RAW output

Set to [On] for RAW movie output at resolutions up to 6K from the HDMI terminal to compatible devices.

As recording begins, the movies are also recorded to card [Card 2] (if it is in the camera) in MP4 format.

You can restrict recording to external recording devices when card [Card 2] is not inserted by setting [Rec Command] to [On] ().

Set the movie recording quality in [Shooting: Movie rec. size] ().

Caution

  • Movies will not be displayed correctly unless the connected device is compatible with the camera's HDMI RAW output.
  • [HDMI RAW output] is not available in [Scene Intelligent Auto (movies)] mode.
  • HDMI RAW output is set to Canon Log 3 and cannot be changed.
  • Image display on external recording devices conforms to the device settings and differs from display on the camera.
  • Movies recorded to card Card 2 conform to the image settings configured on the camera.
  • Some restrictions apply to the following features when the camera is set to HDMI RAW output.
    • MovieISO speed settings
    • Set-up: Record func+card/folder sel.
  • The following features are not available when the camera is set to HDMI RAW output.
    • High Frame Rate movies
    • Digital zoom
    • HDR shooting HDR PQ
    • Auto Lighting Optimizer
    • Highlight tone priority
    • Picture Style
    • Clarity
    • Shooting creative filters
    • Focus breathing correction for lens aberration correction
    • Pre-recording set.
    • HDR Movie Recording
    • Time-lapse movie
    • Movie Digital IS
    • HDMI display
    • HDMI resolution
    • Magnified image display

Note

  • You can include time code in output to devices compatible with RAW movies by setting [Time code] in the [Shooting: Time code] [HDMI] setting to [On]. With [Rec Command] set to [On], you can also control starting and stopping of movie recording on devices compatible with RAW movies by starting and stopping movie recording on the camera ().