Scene Intelligent Auto
is a fully automatic mode. The camera analyzes the scene and sets the optimum settings automatically. It can also adjust focus automatically on either the still or moving subject by detecting the motion of the subject ().
Set the Mode dial to .
- Read the message and select [OK].
Aim the camera at what you will shoot (the subject).
Essentially, the camera focuses on the closest subject.
AF points (1) are displayed over any faces or eyes detected.
- When a frame (AF point) appears on the screen, aim it over the subject.
Focus on the subject.
Press the shutter button halfway to focus.
If blinks, manually raise the built-in flash.
- You can also focus by tapping a person’s face or other subject on the screen (Touch AF).
- Under low light, the AF-assist beam () is automatically activated if needed.
- Once the subject is in focus, that AF point turns green and the camera beeps (One-Shot AF).
- An AF point in focus on a moving subject turns blue and tracks subject movement (Servo AF).
Take the picture.
- Press the shutter button completely to take the picture.
- The image just captured will be displayed for approx. 2 sec. on the screen.
- To retract the built-in flash, push it down with your fingers.
- Subject movement (whether subjects are still or moving) may not be detected correctly for some subject or shooting conditions.
- AF operation (One-Shot AF or Servo AF) is set automatically when you press the shutter button halfway. Even when automatically set to One-Shot AF, the camera will switch to Servo AF if subject motion is detected while you are pressing the shutter button halfway.
- The mode makes the colors look more impressive in nature, outdoor, and sunset scenes. If you do not obtain the desired color tones, change the mode to a Creative Zone mode () and select a Picture Style other than , then shoot again ().
Minimizing blurred photos
- Be careful about camera shake in handheld shots. To avoid camera shake, consider using a tripod. Use a sturdy tripod that can bear the weight of the shooting equipment. Attach the camera securely to the tripod.
- Using a wireless remote control (sold separately, ) is recommended.
Focusing is not possible (indicated by an orange AF point).
Multiple AF points are displayed simultaneously.
Focus has been achieved at all those points.
The shutter speed display is blinking.
Pictures are too dark.
Raise the built-in flash in advance to enable automatic flash firing, in case subjects in daytime shots are backlit, or when shooting under low light.
Pictures taken with flash are too bright.
Pictures may be bright (overexposed) if you shoot subjects at close range in flash photography. Move away from the subject and shoot again.
The bottom part of pictures taken with flash is unnaturally dark.
Shooting subjects that are too close may make the shadow of the lens visible in your shots. Move away from the subject and shoot again. If you are using a lens hood, try removing it before shooting.
Note the following if you are not using the built-in flash.
- Under low light, when camera shake tends to occur, hold the camera steady or use a tripod. When using a zoom lens, you can reduce the blur caused by camera shake by setting the lens to the wide-angle end.
- When shooting portraits under low light, tell subjects to stay still until you have finished shooting. Any movement as you shoot will make the person look blurry in the picture.
Recomposing the Shot
Depending on the scene, positioning the subject toward the left or right to include a balanced background will result in a picture with better perspective.
Pressing the shutter button halfway to focus on a still subject will lock the focus on that subject. Recompose the shot while keeping the shutter button pressed halfway, and then press the shutter button completely to take the picture. This is called “focus lock.”
- The camera continues to focus on any faces initially detected and focused on, even if you recompose the shot.
Shooting Moving Subjects
Pressing the shutter button halfway tracks moving subjects to keep them in focus.
Keep the subject on the screen as you hold down the shutter button halfway, and at the decisive moment, press the shutter button completely.
By touching icons on the screen, you can adjust settings for drive mode, image quality, Touch Shutter, and Creative Assist.
Shooting with Effects Applied (Creative Assist)
- Read the message and select [OK].
Select an effect.
- Use the dial or keys to select an effect, then press .
Select the effect level and other details.
- Use the dial or keys to set it, then press .
- To reset the setting, press the button, then select [OK].
Creative Assist effects
Select one of the preset effects.
Note that [Saturation], [Color tone 1], and [Color tone 2] are not available with [B&W].
 Background blur
Adjust background blur. Choose higher values to make backgrounds sharper. To blur the background, choose lower values. [Auto] adjusts background blurring to match the brightness. Depending on lens brightness (f/number), some positions may not be available.
Adjust image brightness.
Adjust the vividness of colors.
 Color tone 1
Adjust amber/blue color tone.
 Color tone 2
Adjust green/magenta color tone.
Set the toning effect for monochrome shooting.
- [Background blur] is not available in flash photography.
- These settings are reset when you switch shooting modes or set the power switch to . To save the settings, set [: Retain Creative Assist data] to [Enable].
To save the current setting to the camera, press the button on the [Creative Assist] setting screen, then select [OK]. Up to three presets can be saved as [USER*]. After three have been saved, an existing [USER*] preset must be overwritten to save a new one.