Custom Function Setting Items

You can customize camera features on the [Custom Functions] tab to suit your shooting preferences. Any settings you change from default values are displayed in blue.

C.Fn1

Exposure level increments

Sets 1/2-stop increments for the shutter speed, aperture value, exposure compensation, AEB, flash exposure compensation, etc.

  • 1/3: 1/3-stop

  • 1/2: 1/2-stop

Note

  • Display when set to [1/2-stop] is as follows.

ISO speed setting increments

You can change the manual ISO speed setting increment to a whole stop.

  • 1/3: 1/3-stop
  • 1/1: 1-stop

Note

  • Even if [1-stop] is set, ISO speed will be automatically set in 1/3-stop increments when ISO Auto is set.

Speed from metering/ISO Auto

You can set the ISO speed status after the metering timer ends in cases where, for ISO Auto operation in Program AE/Shutter-priority AE/Aperture-priority AE/Manual exposure/Bulb mode, the camera has adjusted the ISO speed during metering or during the metering timer.

  • Restore Auto after metering: Restore Auto after metering
  • Retain speed after metering: Retain speed after metering

Bracketing auto cancel

You can specify to cancel AEB and white balance bracketing when the power switch is set to Power off.

  • ON: Enable
  • OFF: Disable

Bracketing sequence

The AEB shooting sequence and white balance bracketing sequence can be changed.

  • 0−+: 0, -, +
  • −0+: -, 0, +
  • +0−: +, 0, -
AEB White Balance Bracketing
B/A Direction M/G Direction
0: Standard exposure 0: Standard white balance 0: Standard white balance
−: Underexposure −: Blue bias −: Magenta bias
+: Overexposure +: Amber bias +: Green bias

Number of bracketed shots

The number of shots taken with AEB and white balance bracketing can be changed.

When [Bracketing sequence] is set to [0, -, +], the bracketed shots will be taken as shown in the following table.

  • 3: 3 shots
  • 2: 2 shots
  • 5: 5 shots
  • 7: 7 shots
(1-stop/step increments)
1st Shot 2nd Shot 3rd Shot 4th Shot 5th Shot 6th Shot 7th Shot
3: 3 shots Standard (0) –1 +1
2: 2 shots Standard (0) ±1
5: 5 shots Standard (0) –2 –1 +1 +2
7: 7 shots Standard (0) –3 –2 –1 +1 +2 +3

Note

  • If [2 shots] is set, you can select the + or − side when setting the AEB range. With white balance bracketing, the second shot is adjusted toward the negative side for the B/A or M/G direction.

Safety shift

If the subject brightness changes and the standard exposure cannot be obtained within the autoexposure range, the camera will automatically change the manually selected setting to obtain the standard exposure. [Shutter speed/Aperture] applies to Shutter-priority AE or Aperture-priority AE mode. [ISO speed] applies to Program AE, Shutter-priority AE, or Aperture-priority AE mode.

  • OFF: Disable
  • Tv/Av: Shutter speed/Aperture
  • ISO: ISO speed

Note

  • Safety shift overrides any changes to [ISO speed range] or [Min. shutter spd.] from default settings in [Shooting: StillsISO speed settings] if standard exposure cannot be obtained.
  • The minimum and maximum limits for the safety shift with the ISO speed are determined by [Auto range] (). However, if the manually set ISO speed exceeds the [Auto range], the safety shift will take effect up or down to the manually set ISO speed.
  • Safety shift will take effect as necessary even when flash is used.

C.Fn2

Same expo. for new aperture

The maximum aperture value may decrease (the lowest f/number may increase) in Manual exposure mode (manual exposure shooting) with ISO speed set manually (except when set to ISO Auto) if you (1) Change lenses, (2) Attach an extender, or (3) Use a zoom lens with a variable maximum aperture value. This function prevents the corresponding underexposure by adjusting ISO speed or shutter speed (Tv value) automatically to maintain the same exposure as before (1), (2), or (3).

With [ISO speed/Shutter speed], the ISO speed is automatically adjusted within the ISO speed range. If exposure cannot be maintained by adjusting ISO speed, shutter speed (Tv value) is automatically adjusted.

  • OFF: Disable
  • ISO: ISO speed
  • ISO/Tv: ISO speed/Shutter speed
  • Tv: Shutter speed

Caution

  • Does not respond to changes in effective aperture value from changes in magnification when macro lenses are used.
  • Cannot provide the same exposure as before (1), (2), or (3) if [ISO speed] is set and the exposure cannot be maintained at speeds set in [ISO speed range].
  • Cannot provide the same exposure as before (1), (2), or (3) if [Shutter speed] is set and the exposure cannot be maintained at speeds set in [Custom Functions: Set shutter speed range].
  • Shutter speed is limited to 1/8000 when [Shooting: Shutter mode] is [Electronic] and [Same expo. for new aperture] is set to [Shutter speed] or [ISO speed/Shutter speed].

Note

  • Also responds to changes in the highest f/number (minimum aperture).
  • The original exposure setting is restored if you perform (1), (2), or (3) with [ISO speed], [ISO speed/Shutter speed], or [Shutter speed] set and do not adjust ISO speed, shutter speed, or aperture value before returning the camera to the original state, before (1), (2), or (3).
  • Shutter speed may change to maintain exposure if the ISO speed increases to an expanded ISO speed when [ISO speed] is set.

AE lock meter. mode after focus

For each metering mode, you can specify whether to lock the exposure (AE lock) once subjects are in focus with One-Shot AF. The exposure will be locked while you keep pressing the shutter button halfway. Select metering modes for AE lock and add a checkmark [Check]. Select [OK] to register the setting.

Set shutter speed range

You can set the shutter speed range for each [Shooting: Shutter mode] option. In Flexible-priority AE, Shutter-priority AE, or Manual exposure mode, you can set the shutter speed manually within your specified range. In Program AE and Aperture-priority AE mode, or in Flexible-priority AE mode with shutter speed set to [AUTO], the shutter speed is set automatically within your specified range (except for movie recording). Select [OK] to register the setting.

  • Mech shutter/elec 1st-curtain

    • Lowest speed: Can be set in a range of 30 sec.–1/2000 sec.
    • Highest speed: Can be set in a range of 1/4000 sec.–15 sec.
  • Electronic

    • Lowest speed: Can be set in a range of 30 sec.–1/8000 sec.
    • Highest speed: Can be set in a range of 1/16000* sec.–15 sec.

      When set to [High-speed continuous shooting plus]: 1/4000 sec.

Caution

  • Shutter speed is limited to 1/4000 when [Shooting: Shutter mode] is [Electronic] and [Shooting: Drive mode] is set to [High-speed continuous shooting plus].

Set aperture range

You can set the aperture value range. In Flexible-priority AE, Aperture-priority AE, Manual exposure, or Bulb mode, you can set the aperture value manually within your specified range. In Program AE and Shutter-priority AE mode, or in Flexible-priority AE mode with the aperture value set to [AUTO], the aperture value is set automatically within your specified range. Select [OK] to register the setting.

  • Max. aperture

    Can be set in a range of f/1.0–f/64.

  • Min. aperture

    Can be set in a range of f/91–f/1.4.

Note

  • The available aperture value range varies depending on the lens's minimum and maximum aperture value.

C.Fn3

Main DialQuick Control Dial direction to set Tv/Av

Dial turning direction when setting the shutter speed and aperture value can be reversed.

Reverses the turning direction of the Main dial and Quick control dial dials in Manual exposure shooting mode and only the Main dial dial in other shooting modes. The direction of the Quick control dial dial in Manual exposure mode matches the direction to set exposure compensation in Program AE, Shutter-priority AE, and Aperture-priority AE modes.

  • Normal: Normal
  • Reverse direction: Reverse direction

direction to set Tv/Av

RF lens and mount adapter control ring turning direction when setting the shutter speed and aperture value can be reversed.

  • Normal: Normal
  • Reverse direction: Reverse direction

Switch Main Dial/Quick Control Dial when shooting

Functions assigned to the Main dial and Quick control dial can be reversed.

  • OFF: Disable
  • ON: Enable

Customize buttons

You can assign frequently used functions to camera buttons that are easy for you to use. Different functions, for use when shooting still photos or movies, can be assigned to the same button.

  1. Select [Custom Functions: Customize buttons].

  2. Select a camera control.

  3. Select a function to assign.

    • Press the Quick Control/Set button to set it.
    • You can configure advanced settings for functions labeled with [INFODetail set.] in the lower left of the screen by pressing the INFO button.

Note

  • [Custom Functions: Customize buttons] settings are not cleared even if you select [Custom Functions: Clear all Custom Func. (C.Fn)]. To clear the settings, select [Custom Functions: Clear customized settings].

Functions available for customization

AF

●: Default ○: Available for customization
Shutter button half-press Movie button AF-ON AE lock button AF point button Depth-of-field preview button Lens button Multifunction button SET button Up key Down key Left key Right key Multi-controller
Metering and AF start: Metering and AF start
- - - - - - - - -
AF stop: AF stop
- - - - - - - -
AF point selection: AF point selection
- -
Direct AF point selection: Direct AF point selection
- - - - - - - - -
Set AF point to center: Set AF point to center
- -
Start or stop tracking: Start/stop tracking
- ●*4 -
One-Shot AF/Servo AF: One-Shot AF Select Servo AF*1
- -
Eye Detection AF: Eye Detection AF*1
- - - - - - - - - -
Eye Detection: Eye detection
- -
Peaking: Peaking
- -
Focus Guide: Focus guide
- -
Drive modes: Drive mode*1
- ●*2 -

1: Cannot be assigned as a function available in movie recording.

2: Default in still photo shooting.

4: Default in movie recording.

Exposure

●: Default ○: Available for customization
Shutter button half-press Movie button AF-ON AE lock button AF point button Depth-of-field preview button Lens button Multifunction button SET button Up key Down key Left key Right key Multi-controller
Metering start: Metering start
- - - - - - - - - - - - -
AE lock: AE lock
- - - - - - - -
AE lock (hold): AE lock (hold)
- ●*4 - - - - - - -
AE lock, AF stop: AE lock, AF stop
- - - - - - - -
AE lock (while button pressed): AE lock (while button pressed)*1
- - - - - - - - - - - - -
AE lock/FE lock: AE lock/FE lock*1
- ●*3 - - - - - - -
Release AE Lock: Release AE Lock
- - - - - - - -
Exposure compensation (hold button, turn Main dial): Expo comp (hold btn, turn Main Dial)
- - - - - - - - -
ISO: ISO speed
- -
Set ISO speed (hold button, turn Main dial): Set ISO speed(hold btn,turnMain Dial)
- - - - - - - - -
Flash: Flash firing*1
- ●*3 -
FE lock: FE lock*1
- - - - - - - -

1: Cannot be assigned as a function available in movie recording.

3: Default in still photo shooting.

4: Default in movie recording.

Image

●: Default ○: Available for customization
Shutter button half-press Movie button AF-ON AE lock button AF point button Depth-of-field preview button Lens button Multifunction button SET button Up key Down key Left key Right key Multi-controller
Image quality: Image quality*1
- -
One-touch image quality setting: One-touch image quality setting*1
- -
One-touch image quality (hold): One-touch image quality (hold)*1
- -
Still Image Aspect Ratio: Still img aspect ratio*1
- -
Auto Lighting Optimizer: Auto Lighting Optimizer
- -
White Balance: White balance
- -
Picture Style selection: Picture Style
- -
RAW burst: RAW burst mode*1
- -
Protect: Protect
- - - - - - - -
Rating: Rating
- - - - - - - -
Selecting a Folder: Select folder
- -

1: Cannot be assigned as a function available in movie recording.

Movies

●: Default ○: Available for customization
Shutter button half-press Movie button AF-ON AE lock button AF point button Depth-of-field preview button Lens button Multifunction button SET button Up key Down key Left key Right key Multi-controller
Zebra: Zebra*2
- - -
Movies: Movie recording
- - - - - - -
Pause Movie Servo AF: Pause Movie Servo AF
- ●*4 -
Digital Zoom: Digital zoom*2
- - -

2: Cannot be assigned as a function available in still photo shooting.

4: Default in movie recording.

Operation

●: Default ○: Available for customization
Shutter button half-press Movie button AF-ON AE lock button AF point button Depth-of-field preview button Lens button Multifunction button SET button Up key Down key Left key Right key Multi-controller
Flash Function Settings: Flash function settings*1
- -
Dial function settings: Dial function settings
- -
Depth-of-field preview: Depth-of-field preview*1
- - ●*3 - - - - - -
Reset selected item in Fv mode: Reset selected item in Fv mode*1
- -
Reset Tv/Av/exposure/ISO in Fv mode: Reset Tv/Av//ISO in Fv mode*1
- ●*3 -
Quick Control screen: Quick Control screen*1
- -
Magnify or reduce: Magnify/Reduce
- -
Image Playback: Image replay
- -
Magnify images during playback: Magnify images during playback
- -
Menu display: Menu display
- -
Touch Shutter: Enable: Touch Shutter*1
- -
Create folder: Create folder*1
- -
Optical Viewfinder Simulation: OVF sim. view assist*1
- -
Maximize screen brightness (temporary): Maximize screen brightness (temp)
- -
Power off: Power off
- - - - - - -
Screen off: Screen off
- -
Silent Shutter Function: Silent shutter function*1
- -
Switch focus/control ring: Switch focus/control ring
- -
Switch between viewfinder/screen: Switch between VF/screen
- -
Wireless features: Wi-Fi/Bluetooth connection
- -
No function (disabled): No function (disabled)
- ●*4 ●*4

1: Cannot be assigned as a function available in movie recording.

3: Default in still photo shooting.

4: Default in movie recording.

Note

  • [Lens button]: “AF Stop” or “Lens Function” button on super telephoto lenses with Image Stabilizer.

Customize dials

Frequently used functions can be assigned to the Main dial, Quick control dial, and Control ring dials.

  1. Select [Custom Functions: Customize dials].

  2. Select a camera control.

  3. Select a function to assign.

    • Press the Quick Control/Set button to set it.

Note

  • [Custom Functions: Customize dials] settings are not cleared even if you select [Custom Functions: Clear all Custom Func. (C.Fn)]. To clear the settings, select [Custom Functions: Clear customized settings].
  • Setting [Custom Functions: Switch Main Dial/Quick Control Dial when shooting] to [Enable] also changes the functions you can assign.

Functions available for dials

●: Default ○: Available for customization
Function Main dial Quick control dial Control ring
Select AF area Select AF area
AF area (hold metering button) AF area (hold metering button)
Change shutter speed Change shutter speed
Change aperture value Change aperture value
Exposure compensation Exposure compensation
ISO Set ISO speed
Change shutter speed (while pressing metering button) Change shutter spd. (hold meter. btn)
Change aperture value (while pressing metering button) Change aperture (hold meter. btn)
Exposure compensation (hold button, turn Main dial) Exposure comp. (hold meter. btn)
Set ISO speed (hold button, turn Main dial) Set ISO speed (hold meter. btn)
Flash exposure compensation (while pressing metering button) Flash exp comp (hold meter.btn)
Shutter speed setting in M mode Shutter speed setting in M mode
Aperture value setting in M mode Aperture setting in M mode
White balance selection White balance selection
Select color temperature Select color temperature
Picture Style selection Picture Style
Select WB (while pressing metering button) Select WB (hold meter. btn)
Color temperature (while pressing metering button) Color temp. (hold meter. btn)
Select Picture Style (while pressing metering button) Select Picture style (hold meter. btn)
No function (disabled) No function (disabled)

Note

  • Control ring: Control ring on RF lenses and mount adapters.

Clear customized settings

  1. Select [Custom Functions: Clear customized settings].

  2. Select [OK].

    • [Customize buttons] and [Customize dials] are restored to defaults.

C.Fn4

Add cropping information

Adding cropping information displays vertical lines for the aspect ratio specified in shooting, so that you can compose shots as if shooting with a medium- or large-format camera (6×6 cm, 4×5 inch, and so on).

When you shoot, instead of cropping images recorded to the card, the camera adds aspect ratio information to images for cropping in the Digital Photo Professional (EOS software).

You can import images to Digital Photo Professional on a computer and easily crop images to the aspect ratio set at the time of shooting.

  • OFF: Disable
  • 6:6: Aspect ratio 6:6
  • 3:4: Aspect ratio 3:4
  • 4:5: Aspect ratio 4:5
  • 6:7: Aspect ratio 6:7
  • 5:6: Aspect ratio 10:12
  • 5:7: Aspect ratio 5:7

Caution

  • Cropping information can only be added when [Shooting: Still img aspect ratio] is set to [3:2].
  • JPEG or HEIF images are not saved at the cropped size if you use the camera to process RAW images with cropping information (). In this case, RAW processing produces JPEG or HEIF images with cropping information.

Note

  • Vertical lines indicating your specified aspect ratio are displayed on the screen.

Default Erase option

You can set which option is selected by default in the erase menu (), which is accessed by pressing the Erase button during image playback or during review after shooting.

By setting an option other than [Cancel], you can simply press the Quick Control/Set button to erase images quickly.

  • Cancel: [Cancel] selected
  • Erase: [Erase] selected
  • RAW: [EraseRAW] selected
  • J/H: [Erase non-RAW] selected

Caution

  • Be careful not to erase images accidentally when an option other than [Cancel] is set.

Release shutter w/o lens

You can specify whether shooting still photos or movies is possible without a lens attached.

  • OFF: Disable
  • ON: Enable

Retract lens on power off

You can set whether to retract gear-type STM lenses (such as RF35mm F1.8 Macro IS STM) automatically when the camera's power switch is set to Power off.

  • ON: Enable
  • OFF: Disable

Caution

  • With auto power off, the lens will not retract regardless of the setting.
  • Before detaching the lens, make sure that it is retracted.

Note

  • When [Enable] is set, this function takes effect regardless of the setting of the focus mode switch (AF or MF) on the camera or lens.

C.Fn5

Clear all Custom Func. (C.Fn)

Selecting [Custom Functions: Clear all Custom Func. (C.Fn)] clears all Custom Function settings except [Customize buttons] and [Customize dials].

Note

  • To clear settings configured with [Custom Functions: Customize buttons] and [Custom Functions: Customize dials], select [Custom Functions: Clear customized settings].