Part Names

  1. (1) Self-timer lamp/AF-assist beam
  2. (2) Shutter button
  3. (3) Multi-function button 2 (M-Fn 2)
  4. (4) Depth-of-field preview button
  5. (5) Grip
  6. (6) Vertical-grip Multi-function button
  7. (7) Vertical-grip Main dial
  8. (8) Vertical-grip shutter button
  9. (9) RF lens mount index
  10. (10) Lens mount
  11. (11) Lens lock pin
  1. (12) Lens release button
  2. (13) Shutter curtain/Image sensor
  3. (14) Remote control terminal
  4. (15) Contacts
  5. (16) Vertical-grip depth-of-field preview button
  6. (17) Vertical-grip Multi-function button 2 (M-Fn 2)
  7. (18) Tripod socket
  8. (19) Serial number (body number)
  9. (20) Accessory positioning hole
  10. (21) Body cap
  1. (1) Eyecup
  2. (2) Multi-function shoe
  3. (3) Flash sync contacts
  4. (4) Focal plane mark
  5. (5) Drive mode/AF operation selection button
  6. (6) Microphone
  7. (7) Flash exposure compensation/metering mode selection button
  8. (8) Strap mount
  9. (9) External microphone IN terminal
  10. (10) Digital terminal
  11. (11) HDMI micro OUT terminal
  12. (12) Headphone terminal
  13. (13) Ethernet RJ-45 terminal
  14. (14) PC terminal
  15. (15) Terminal cover
  16. (16) Battery release handle
  1. (17) Battery
  2. (18) Battery compartment cap
  3. (19) LCD panel
  4. (20) LCD panel info switching/illumination button
  5. (21) Exposure compensation/aperture value setting button
  6. (22) Mode button
  7. (23) AF point selection button
  8. (24) AE lock button
  9. (25) Quick control dial 2
  10. (26) AF start button/Smart controller
  11. (27) Quick Control button
  12. (28) Access lamp
  13. (29) Power/multi-function lock switch
  14. (30) Speaker
  15. (31) Screen
  16. (32) Menu button
  17. (33) / Rating/voice memo button
  1. (1) Viewfinder eyepiece
  2. (2) Multi-controller (can also be pressed straight in)
  3. (3) Info button
  4. (4) Set button
  5. (5) Quick control dial 1
  6. (6) Playback button
  7. (7) Network lamp
  8. (8) Magnify/reduce button
  9. (9) Erase button
  10. (10) Dioptric adjustment knob
  11. (11) Still photo shooting/ movie recording switch
  1. (12) Multi-function button
  2. (13) Main dial
  3. (14) Strap mount
  4. (15) Movie shooting button
  5. (16) Card slot 1
  6. (17) Card slot 2
  7. (18) Card slot cover
  8. (19) Card 1 eject button
  9. (20) Vertical-grip Multi-controller (can also be pressed straight in)
  10. (21) Vertical-grip AF start button/Smart controller
  11. (22) Vertical-grip Quick control dial 2
  12. (23) Vertical-grip AE lock button
  13. (24) Vertical-grip AF point selection button

LCD panel information display

Information displayed varies depending on camera status. For icon details, see Information Display.

Viewfinder information display

Information displayed varies depending on camera status.

Battery Pack LP-E19

  1. (1) Battery lock lever
  2. (2) Contacts
  1. (3) Protective cover
  2. (4) Battery release handle

Battery Charger LC-E19

Charger for Battery Pack LP-E19 ().

  1. (1) Contacts
  2. (2) Battery slots
  3. (3) Power cord socket
  4. (4) Recharge performance check button/Calibration button
  1. (5) Charge lamp/Recharge performance check lamp/Discharge time lamp
  2. (6) Calibration (discharge) lamp
  3. (7) Protective cover (two included)
  4. (8) Power cord

Attaching the Strap

Pass the end of the strap through the strap mount from the bottom, then pass it through the strap buckle as shown. Pull the strap to take up any slack and make sure the strap will not loosen from the buckle.

Using the Cable Protector

  • When connecting the camera to a computer, use the included interface cable or a Canon cable.
  • Use a commercially available HDMI cable when connecting the camera to a monitor or other display device.
  • When connecting an interface cable, use the included cable protector. Using the cable protector helps prevent accidental disconnection and terminal damage.

Preparation

The cable protector consists of the protector (1) and a clamp (2).

Attach the protector to the camera.

With the included interface cable and a slim commercially available HDMI cable

    • (3) Included interface cable
    • (4) Slim commercially available HDMI cable

With an included or optional Canon interface cable and a thick commercially available HDMI cable

    • (5) Included or optional Canon interface cable
    • (6) Thick commercially available HDMI cable

With only an optional Canon interface cable or a commercially available HDMI cable

When using only an optional Canon interface cable or a thick/slim commercially available HDMI cable, pass the cable through the clamp (2) as shown before attaching the clamp to the cable protector.

Caution

  • Using the camera when an interface cable or HDMI cable is connected without the cable protector may damage the camera terminal. Make sure each cable is securely connected to the camera terminal.