Configuring Detailed Settings of Basic Settings

If you select [Basic Settings] and click [Detailed Settings], the settings tabs are displayed. Switch the settings tabs to configure the MREAL Display, MREAL space, and other detailed settings

Note

  • There are settings tabs that are not displayed depending on the settings of [Basic Settings].

[Main Camera] Tab

Adjust the white balance and exposure (brightness) of the main camera of the MREAL Display.

White Balance

With the MREAL S1/X1, the white balance is adjusted automatically if you select [Auto Settings].

To adjust the white balance by color temperature, move the slider. You can check the results of adjustment in the Preview window.

For a model with [Use the White Balance Setting Tool] displayed, you can adjust the white balance using a white reference with the following procedure.

  1. Place white paper (white reference) within the MREAL space.

  2. Click [Start Tool].

    • White Balance Tool launches and the following window appears.

  3. Adjust the white reference so that it is within the red frame.

  4. Click [Adjust within Frame].

  5. Click [OK].

Exposure

  • To adjust the brightness automatically, select [Auto Settings]. If you move the slider of [Auto Exposure Shift Quantity], exposure correction is performed in the auto setting status.
  • To configure the settings manually, select [Manual Settings] and make adjustments with the sliders of [Shutter Speed] and [Gain].
  • For a model with [Release the Upper Limit of Gain] displayed, if you place a check mark in the checkbox, a gain correction value upper limit of up to 30.00 dB is enabled and the gain is adjusted automatically within the range of 0 to 30.00 dB.
  • You can check the results of adjustment in the Preview window.

[Registration Camera] Tab

White Balance (MREAL Display MD-10)

To adjust the white balance by color temperature, move the slider. You can check the results of adjustment in the Preview window.

Exposure Correction

Adjust the brightness of the registration camera image of the MREAL Display.

  • To adjust the brightness automatically, select [Auto Settings].
  • For a model with [Release the Upper Limit of Gain] displayed, if you place a check mark in the checkbox, a gain correction value upper limit of up to 30.00 dB is enabled and the gain is adjusted automatically within the range of 0 to 30.00 dB.
  • If you move the slider of [Auto Exposure Shift Quantity], exposure correction is performed in the auto setting status.
  • To configure the settings manually, select [Manual Settings] and make adjustments with the sliders of [Shutter Speed] and [Gain]. You can check the results of adjustment in the Preview window.

[Sensor] Tab

This is displayed when using an external sensor for the camera tracking method. Adjust the delay of the signal from the external sensor when, for example, the 3D CG is blurred or the target is not tracked. When the 3D CG is displayed late with respect to the movement in the image, move the slider in the + direction. When the 3D CG is displayed early, move the slider in the - direction.

[Display] Tab

Adjust how the MREAL image displayed in the MREAL Display appears.

Display Position and Size

Adjust the size and position of the area in which the MREAL image is displayed. If you clear the check mark from [Auto Settings], you can make adjustments.

Adjust Stereoscopy

If you feel there is something wrong with the stereoscopic images, adjust the size and position of the MREAL images.

  1. Place a check mark in [Enable], and click [Edit].

    • Image Setting Tool launches and the following window appears.

  2. Make adjustments by moving the sliders.

    • [Display Position] allows you to adjust the spacing between images on the left eye side and right eye side.
    • [Scale] allows you to adjust the size of the MREAL images.
    • To return to the status before adjustment, click [Reset].
    • When adjustment is finished, click [OK].

Display Panel Settings

Placing a check mark in [Low Latency mode] reduces the delay in image display.

Placing a check mark in [Low Afterimage mode] reduces the blurring caused by afterimages.

Placing a check mark in [Video Smoothing Mode] reduces the dropped frames in the MREAL images.

Caution

  • When the dropped frames are noticeable, clear the check mark from [Video Smoothing Mode] and check the operating environment.
  • [Video Smoothing Mode] does not affect external monitor output.

Luminance Settings

Adjust the luminance of the MREAL images according to the lighting, external light environment, and other conditions in the location of use.

Monitor Output Settings

Configure the settings for output to an external monitor (Full HD [1920×1080] or WQXGA [2560×1600]).

Other

Set the following as necessary when using an OpenXR compatible application.

Background Image and CG Delay Reduction Setting

When the delays in the movement of the 3D CG are noticeable relative to the background image, place a check mark in [Reduces Application Delays].

Transparency Setting of CG to be Combined with Background Image

If the relationship between the background image and CG transparency is unnatural, place a check mark in [Invert Transparency].

Marker Canceller

To use external monitors in the MREAL space, place a check mark in [Display]. This prevents markers displayed on external monitors from being detected erroneously by the MREAL Display.

Note

  • The menus and items that are displayed differ depending on the model.

[Spatial Features] Tab

This is displayed when using spatial features for the camera tracking method. For details on spatial features, see “Spatial Features”.

[Coordinate System] Tab

Configure the settings of the world coordinate system.

Gravity Direction in the World Coordinate System

Specify the gravity direction (downward).

Align the Origin of the World Coordinate System with the Origin of the Tracking Sensor

When using an external sensor for the camera tracking method, align the origin of the world coordinate system with the origin of the external sensor coordinate system.