Basic Communication Settings

Before using the following camera communication functions, configure camera and computer settings as described starting in Preparation.

  • Connect to a smartphone via Wi-Fi without using Bluetooth
  • Upload images to a Web service

Preparation

Preparing to use communication functions

  • EOS Utility

    A computer with EOS Utility (EOS software) installed is required.

    For EOS Utility installation instructions, visit the Canon website.

  • GPS

    See GPS Settings.

Caution

  • Transferring movies

  • Each movie file is large, and transferring large files over Wi-Fi may take some time. Referring to Wireless Communication Function Precautions, arrange your network environment for stable communication between devices and the access point.

Checking the Type of Access Point

When connecting via an access point, check whether the access point supports WPS*, which simplifies connections between Wi-Fi devices.

If you are unsure about WPS compatibility, refer to the access point user manual or other documentation.

Stands for Wi-Fi Protected Setup.

  • When WPS is supported

    Two connection methods are available, as follows. You can connect more easily via WPS in PBC mode.

    • Connecting via WPS (PBC mode) ()
    • Connecting via WPS (PIN mode) ()

  • When WPS is not supported

    • Connecting manually to detected networks ()
    • Connecting manually by specifying networks ()

Access point encryption

The camera supports the following options for [Authentication] and [Encryption settings]. For this reason, the encryption used by the access point must be set to one of the following when you will connect to detected networks manually.

  • [Authentication]: Open system, shared key, or WPA/WPA2/WPA3-Personal
  • [Encryption settings]: WEP, TKIP, or AES

Caution

  • Connections may not be possible when access point stealth functions are enabled. Deactivate stealth functions.
  • Ask any network administrator in charge of networks you will join for setting details.

Note

  • If MAC address filtering is used on networks you will join, add the camera's MAC address to the access point. The MAC address can be checked on the [MAC address] screen ().

Connecting via WPS (PBC Mode)

Instructions in this section are continued from Checking the Type of Access Point.

This is a connection method used with access points compatible with WPS. In pushbutton connection mode (PBC mode), the camera and access point can be connected simply by pressing the WPS button on the access point.

  • Connecting may be more difficult if multiple access points are active nearby. If so, try to connect with [WPS (PIN mode)].
  • Check the position of the WPS button on the access point in advance.
  • It may take approx. 1 min. to establish a connection.

  1. Select [Connect with WPS] on the [Select a network] screen.

  2. Select [WPS (PBC mode)].

    • Select [OK].

  3. Connect to the access point.

    • Press the access point's WPS button. For details on where the button is and how long to press it, refer to the access point user manual.
    • Select [OK] to initiate connection with the access point.
    • The following screen is displayed once the camera is connected to the access point.

  4. Set the IP address.

Connecting via WPS (PIN Mode)

Instructions in this section are continued from Checking the Type of Access Point.

This is a connection method used with access points compatible with WPS. In PIN code connection mode (PIN mode), an 8-digit identification number indicated on the camera is entered on the access point to establish a connection.

  • Even if multiple access points are active nearby, connecting by using this shared identification number is relatively reliable.
  • It may take approx. 1 min. to establish a connection.

  1. Select [Connect with WPS] on the [Select a network] screen.

  2. Select [WPS (PIN mode)].

    • Select [OK].

  3. Enter the PIN code.

    • On the access point, enter the 8-digit PIN code displayed on the camera screen.
    • For instructions on entering PIN codes on the access point, refer to the access point user manual.
    • After entering the PIN code, select [OK] on the camera.

  4. Connect to the access point.

    • Select [OK] to initiate connection with the access point.
    • The following screen is displayed once the camera is connected to the access point.

  5. Set the IP address.

Connecting Manually to Detected Networks

Instructions in this section are continued from Checking the Type of Access Point.

Connect to an access point by selecting its SSID (or ESS-ID) in a list of active access points nearby.

Selecting the access point

  1. Select an access point on the [Select a network] screen.

    • (1) SSID
    • (2) Security icon (only for encrypted access points)
    • (3) Channel used
    • Use the Up keyDown key keys to select the access point to connect to in the list of access points.

Note

  • [Refresh]

  • To display [Refresh], scroll down the screen in step 1.
  • Select [Refresh] to search for access points again.

Entering the access point encryption key

  • Enter the encryption key (password) set on the access point. For details on the encryption key that has been set, refer to the access point's user manual.
  • The screens displayed in steps 2–3 vary depending on the authentication and encryption set on the access point.
  • Go to Setting the IP Address if the [IP address set.] screen is displayed instead of the screens shown for steps 2–3.

  1. Select a key index.

    • The [Key index] screen is displayed for WEP-encrypted access points.
    • Select the key index number set on the access point.
    • Select [OK].

  2. Enter the encryption key.

    • Press the Quick Control/Set button to access the virtual keyboard (), then enter the encryption key.
    • Select [OK] to initiate connection with the access point.
    • The following screen is displayed once the camera is connected to the access point.

  3. Set the IP address.

Connecting Manually by Specifying Networks

Instructions in this section are continued from Checking the Type of Access Point.

Connect to an access point by entering its SSID (or ESS-ID).

Entering the SSID

  1. Select [Manual settings] on the [Select a network] screen.

  2. Enter the SSID (network name).

    • Press the Quick Control/Set button to access the virtual keyboard (), then enter the encryption key.
    • Select [OK].

Setting the access point authentication method

  1. Select the authentication method.

    • Select an option and then [OK] to go to the next screen.
    • On the [Encryption settings] screen displayed if [Open system] is selected, select [Disable] or [WEP].

Entering the access point encryption key

  • Enter the encryption key (password) set on the access point. For details on the encryption key that has been set, refer to the access point's user manual.
  • The screens displayed in steps 4–5 vary depending on the authentication and encryption set on the access point.
  • Go to Setting the IP Address if the [IP address set.] screen is displayed instead of the screens shown for steps 4–5.

  1. Select a key index.

    • The [Key index] screen is displayed if you have selected [Shared key] or [WEP] in step 3.
    • Select the key index number set on the access point.
    • Select [OK].

  2. Enter the encryption key.

    • Press the Quick Control/Set button to access the virtual keyboard (), then enter the encryption key.
    • Select [OK] to initiate connection with the access point.
    • The following screen is displayed once the camera is connected to the access point.

  3. Set the IP address.

Connecting in Camera Access Point Mode

Camera access point mode is a connection method for directly connecting the camera and other devices via Wi-Fi without using an access point. Two connection methods are available, as follows.

Caution

  • Some printers may not be able to connect when the camera is used as an access point.

    If connection in camera access point mode is not possible, you may be able to establish a connection as follows.

    • Establish a Wi-Fi connection via an access point
    • Start access point mode on the printer

Connecting with Easy connection

Network settings for camera access point mode are configured automatically.

  • For instructions on using the devices you will connect to, refer to the device instruction manual.

  1. Select [Camera access point mode] on the [Select a network] screen.

  2. Select [Easy connection].

    • Select [OK].

  3. Use the other device to connect to the camera.

    • (1) SSID (network name)
    • (2) Encryption key (password)
    • In other device's Wi-Fi settings, select the SSID (network name) shown on the camera screen, then enter the password.

  4. Complete the connection settings based on the device to connect to.

    • If a Wi-Fi connection cannot be established, set [Security] on the camera to [WPA2] ().

Connecting with Manual connection

Network settings for camera access point mode are configured manually. Set [SSID], [Channel setting], and [Encryption settings] on each screen displayed.

  1. Select [Manual connection].

    • Select [OK].

  2. Enter the SSID (network name).

    • Press the Quick Control/Set button to access the virtual keyboard (), then enter the SSID. After input, press the MENU button.
    • Select [OK].

  3. Select a channel setting option.

    • To specify the settings manually, select [Manual setting], then turn the Dial dial.
    • Select [OK].

  4. Select an encryption setting option.

    • For encryption, select [AES].
    • Select [OK].
    • When [AES] is selected, the [Password] screen is displayed. Press the Quick Control/Set button to access the virtual keyboard (), then enter the encryption key. After input, press the MENU button.

  5. Select [Auto setting].

    • Select [OK].
    • If an error is displayed for [Auto setting], set the IP address manually ().

  6. Use the other device to connect to the camera.

    • (1) SSID (network name)
    • (2) Encryption key (password)

  7. Complete connection settings for the communication function.

    • If a Wi-Fi connection cannot be established, set [Security] on the camera to [WPA2] ().

Setting the IP Address

Select a method of setting the IP address, and then set the IP address on the camera. When IPv6 is used, the camera only connects via IPv6. IPv4 connections are disabled.

Setting the IP address automatically

Set up the IP address settings automatically.

  1. Select [Auto setting].

    • Select [OK].
    • If an error is displayed for [Auto setting], set the IP address manually ().

  2. Select an IPv6 option.

    • Select an option and then [OK] to go to the next screen.
    • Select [Enable] to use IPv6.

  3. Complete the connection settings based on the device to connect to.

Setting the IP address manually

Set up the IP address settings manually. Note that the items displayed vary depending on the communication function.

  1. Select [Manual setting].

    • Select [OK].

  2. Select an option to configure.

    • Select an option to access the screen for numerical input.

    • To use a gateway, select [Enable], then select [Address].

  3. Enter the number.

    • Turn the Dial dial to switch to other input fields at the top of the screen, and press the Left keyRight key keys to select numbers to enter. Press the Quick Control/Set button to enter the selected number.
    • To delete the number just entered, press the MENU button.
    • Select [OK] to confirm input and return to the screen in step 2.

  4. Select [OK].

    • When you have completed setting the necessary items, select [OK]. The next screen is displayed.
    • If you are unsure what to enter, see Checking Network Settings or ask the network administrator or other person in charge of the network.

  5. Select an IPv6 option.

    • Select an option and then [OK] to go to the next screen.
    • Select [Enable] to use IPv6.

  6. Complete the connection settings based on the device to connect to.