Flash Function Settings

Functions of the built-in flash or external EL/EX series Speedlites can be set from menu screens on the camera.

Before setting functions of external Speedlites, attach the Speedlite and turn it on.

For details on external Speedlite functions, refer to the Speedlite’s instruction manual.

  1. Select [Shooting: Flash control].

  2. Select an option.

Flash Firing

  • Set to [Automatic firing] (in Basic Zone or Program AE modes) to have the flash fire automatically, based on shooting conditions.

  • Set to [Fire] to have the flash always fire when you shoot.

  • Select [Flash off] (in Creative Zone modes) to keep the flash off, or if you will use the AF-assist beam.

E-TTL II Flash Metering

  • Set to [Eval (FacePrty)] for flash metering suitable for shots of people. Continuous shooting speed for [High-speed continuous shooting] is slower than when [Evaluative] or [Average] is selected.

  • Set to [Evaluative] for flash metering that emphasizes firing in continuous shooting.

  • If [Average] is set, the flash exposure will be averaged for the entire metered scene.

Caution

  • Even when [Eval (FacePrty)] is set, some subjects and shooting conditions may prevent you from obtaining the expected result.

Red-Eye Reduction

Set to [Enable] to reduce red-eye by firing the red-eye reduction lamp before firing the flash.

Slow Synchro

You can set the flash-sync speed for flash photography in Aperture-priority AE mode or Program AE mode.

Caution

  • To use slow-sync shooting in Aperture-priority AE/Program AE mode, set to [1/200-30sec. auto].

Built-in Flash Function Settings

Flash mode

Set to [E-TTL II] to shoot in E-TTL II/E-TTL fully automatic flash mode.

Set to [Manual flash] to specify your preferred flash output in [Built-in flashflash output].

  • Only available in Tv/Av/M modes.

Shutter sync.

Normally, set to [1st curtain] so that the flash fires immediately after shooting starts.

Set to [2nd curtain] and use low shutter speeds for natural-looking shots of subject motion trails, such as car headlights.

Caution

  • When shooting with [2nd curtain], set a shutter speed of 1/60 sec. or slower. For shutter speeds exceeding 1/60 sec., first-curtain synchronization is used automatically even if [2nd curtain] is set.

Built-in flashexp. comp.

Set the flash exposure compensation if the brightness of the subject does not come out as desired (so you want to adjust the flash output) in flash photography. You can set the flash exposure compensation up to ±2 stops in 1/3-stop increments.

  1. Select [Built-in flashexp. comp.].

  2. Set the compensation amount.

    • If the exposure is too dark, press the Right key key (for increased exposure).
    • If the exposure is too bright, press the Left key key (for decreased exposure).
    • After taking the picture, cancel the flash exposure compensation by setting it back to 0.

Caution

  • Setting [Shooting: Auto Lighting Optimizer] () to an option other than [Disable] may still cause images to look bright even if you set negative flash exposure compensation for darker exposure.
  • If flash exposure compensation is set with a Speedlite (sold separately, ), you cannot set the flash exposure compensation with the camera (Quick Control or external flash function setting). Note that the Speedlite’s setting overrides the camera’s if both are set at the same time.

Note

  • The exposure compensation amount will remain in effect even after you set the power switch to Power off.

External Flash Function Settings

The information displayed on the screen, position of display, and available options vary depending on the Speedlite model, its Custom Function settings, the flash mode, and other factors. Refer to the instruction manual of your flash unit for details on its functions.

Sample display

  1. (1) Flash mode
  2. (2) Wireless functions/Firing ratio control
  3. (3) Flash zoom (flash coverage)
  1. (4) Shutter synchronization
  2. (5) Flash exposure compensation
  3. (6) Flash exposure bracketing

Caution

  • Functions are limited when using EX series Speedlites that are not compatible with flash function settings.

Flash mode

You can select the flash mode to suit your desired flash photography.

  • [E-TTL II] is the standard mode of EL/EX-series Speedlites that support autoexposure flash photography.
  • [Manual flash] is a mode for manually configuring the Speedlite’s [Flash output] setting.
  • [CSP] (Continuous shooting priority mode) is available when using a compatible Speedlite. This mode automatically reduces flash output by one stop and increases ISO speed by one stop. Useful in continuous shooting, and helps conserve flash battery power.
  • Regarding other flash modes, refer to the Instruction Manual of a Speedlite compatible with the respective flash mode.

Caution

  • Adjust Exposure Compensation as needed in case of overexposure from flash photography with [CSP] in Shutter-priority AE/Manual exposure mode.

Note

  • With [CSP], ISO speed is automatically set to [Auto].

Wireless functions

You can use radio or optical wireless transmission to shoot with wireless multiple-flash lighting.

For details on wireless flash, refer to the Instruction Manual of a Speedlite compatible with wireless flash photography.

Firing ratio control

With a macro flash, you can set the firing ratio control.

For details on firing ratio control, refer to the Instruction Manual of the macro flash.

Flash zoom (flash coverage)

With Speedlites having a zooming flash head, you can set the flash coverage.

Shutter synchronization

Normally, set this to [First-curtain synchronization] so that the flash fires immediately after the shooting starts. Set to [Second-curtain synchronization] and use low shutter speeds for natural-looking shots of subject motion trails, such as car headlights.

Set to [High-speed synchronization] for flash photography at higher shutter speeds than the maximum flash sync shutter speed. This is effective when shooting with an open aperture in Aperture-priority AE mode to blur the background behind subjects outdoors in daylight, for example.

Caution

  • When shooting with [Second-curtain synchronization], set a shutter speed of 1/60 sec. or slower. For shutter speeds exceeding 1/60 sec., first-curtain synchronization is used automatically even if [Second-curtain synchronization] is set.

Flash exposure compensation

Just as exposure compensation is adjustable, you can also adjust flash output of external Speedlites.

Caution

  • If flash exposure compensation is set with the Speedlite, you cannot set the flash exposure compensation with the camera. Note that the Speedlite’s setting overrides the camera’s if both are set at the same time.

Flash exposure bracketing

Speedlites equipped with flash exposure bracketing (FEB) can change the external flash output automatically as three shots are taken at once.

External Flash Custom Function Settings

For details on the external Speedlite’s Custom Functions, refer to the Speedlite’s Instruction Manual.

Caution

  • With an EL/EX series Speedlite, the Speedlite will always fire at full output if the [Flash metering mode] Custom Function is set to [1:TTL] (autoflash).
  • Setting or clearing Speedlite Personal Functions (P.Fn) is not possible from the camera’s [Shooting: External flash func. setting] screen. Set them directly from the Speedlite.

Clearing Flash Function Settings/C.Fn Settings

  1. Select [Clear settings].

  2. Select the settings to be cleared.

    • Select [Clear built-in flash set.], [Clear external flash set.], or [Clear ext. flash C.Fn set.].

    • Select [OK] on the confirmation screen to clear all flash settings or Custom Function settings.